Email Us U.S. FREE Shipping
260-273-9909 on order over $100.00

17-338 Cal. Neck Turning Lathe

**Accurate Shooter - Daily Bulletin**
April 8, 2011
http://bulletin.accurateshooter.com/2011/04/new-neck-turning-lathe-from-21st-century-shooting/

Complete with Neck Turning Tool, Swilvel Bracket and Tail Stock Assembly with One Shell Holder & Driver. - ARBORS AND MANDRELS SOLD SEPARATELY.

This is the first in the series of 21st Century Shooting Case Preparation. A modular system, all parts interchange. So if you have our Neck Turning Tool or Bracket everything will fit.
     The floating design of our neck turner and case driver allows the case mouth (bore) to run on the arbor absolutely concentric. Therefore allowing O.D. to be turned concentric with I.D.
     The tail-stock creates a horizontal inline support for the base of the case. Also allows the operator to keep both hands on the power screw driver or drill. This makes it very easy to control feed rate of the cutting operation, generating a very fine turned finish.
     Case holder drivers are designed to be the most gentle driver, yet providing an adequate hold. DOES NOT DRIVE OFF THE PRIMER POCKET - NO PRIMER POCKET OR CASE DAMAGE.
     There are counter sunk mounting holes in the base plate for mounting.

     This lathe is the foundation of many case prep tools. Trimmer, concentricity gage and a means to restore concentricity.
     Driver shaft is hexed to use power screw driver or drill.

A modular system, all parts interchange. So if you have our or everything will fit. The floating design of our neck turner and case driver allows the case mouth (bore) to run on the arbor absolutely concentric. Therefore allowing O.D. to be turned concentric with I.D. The tail-stock creates a horizontal inline support for the base of the case. Also allows the operator to keep both hands on the power screw driver or drill. This makes it very easy to control feed rate of the cutting operation, generating a very fine turned finish. Case holder drivers are designed to be the most gentle driver, yet providing an adequate hold. DOES NOT DRIVE OFF THE PRIMER POCKET - NO PRIMER POCKET OR CASE DAMAGE. There are counter sunk mounting holes in the base plate for mounting. This lathe is the foundation of many case prep tools. Trimmer, concentricity gage and a means to restore concentricity. Driver shaft is hexed to use power screw driver or drill.

Tail-stock base is adjustable to accommodate cases from 17 Fireball to a .416 Rigby.

$245.00 - Pt# 908

Complete with Neck Turning Tool, Swilvel Bracket and Tail Stock Assembly with One Shell Holder & Driver. - ARBORS AND MANDRELS SOLD SEPARATELY.

1. Choose Cutter Degree choice. 2. Choose Case Holder and Driver.

15° Carbide Cutter

Lathe Video 1

Lathe Video 2

Cutter Angle Chart

Case Holder Driver
Number Chart

20° Carbide Cutter

21.5° Carbide Cutter

23° Carbide Cutter

25° Carbide Cutter

28° Carbide Cutter

30° Carbide Cutter

35° Carbide Cutter

40° Carbide Cutter

Arbors Mandrels

Click here for Lathe Video 1

Click here for Lathe Video 2

Lathe base, Swivel Bracket and Tail Stock Assembly with Shell Holder and Driver.

Pt# 909-01 (#2, #3, #4, #5, PPC, L, BR)
$165.00

Lathe base, Tail Stock Assembly with Shell Holder and Driver.

Pt# 909-02 (#2, #3, #4, #5, PPC, L, BR)
$145.00

Shell Holder and Driver with Driver Adapter.

Pt# 906 (#2, #3, #4, #5, PPC, L, BR)
$36.00

Adapter for Shell Holder to fit power screw driver, drill or power head.

Pt# 906
$5.50

Shell Holder with Driver.

Pt# 907 (#2, #3, #4, #5, PPC, L, BR)
$29.50

Lathe Accessory Package
   -(2) orings for Driver Shaft
   -(2) orings for Driver
   -(2) 6/32 set screws for Cutter Holder
   -(1) 10/32 set screw,with point, for Cutter Holder Retainer
   -(1) 10/32 set screw for Driver Adapter

Pt# 908-AP
$4.99